Відео

With the big wheels it surprisingly pushes the rocks out of the way. It doesn’t really compare to traditional skateboard wheels where you come to a dead stop and go flying on the smallest pebble.

Usually doesn't stay on until the controller is paired.

@@barnes_specialty It’s not getting paired. What could be the issue. Used to work properly the set up is same as yours. Been using it for 5 years +

I read an article about why there are no lightning bugs here. They say they are here but they aren’t getting the nutrients they need to light up and their numbers are dwindling in Florida. I grew up in Alabama until I was 10 and I could catch a jar full every night but I’ve not seen one here in Florida I’m in Panama City and frequent orlando and Tampa and have yet to see any.

It’s very flexible when warm but hardens back solid after it cools.

Yes. There isn't much to show it working. Just hook up the batteries, ESC, and ride.

@@barnes_specialty iv just built one copying this video 😂

Wish there was away to have it looked at before i add power 😂

Actually it is fine as it needs to be over 200* F to soften. A lot of police sidearm holsters are made from kydex. It's a great material for this.

Depends on size and thickness. $20-40 to do this. knifekits.com

@@barnes_specialty thanks for that info do you know if they come in bigger sheets and 12 x 12?

Haven’t touched it since I made this video. It is still working well. Is there anything that could be blocking the signal? Make sure it isn’t surrounded by metal.

When there is no load it doesn't pull many amps.

Has one ever broken, No. How about you do something useful and contribute to the community instead of providing useless feedback. This board has run well over 200 miles without problems. I see you have no content on your youtube channel. Are you referring to electric-skateboard.builders the forum that is run by the failure known as Enertion? Keep your mouth shut if you have nothing positive to say.

Barnes'd it broke when you were putting it in. On film. With a screw driver and not the way way way more intense forces that will be put on it when riding. If it hasn’t broken yet it’s shear luck. My post is “contributing” to the community Caus it guides people in the directions where they can learn safely and properly how do to things. Cuz eyeballing shit as you go is def not the way to do shit. You switched your technique halfway through, like you weren’t even sure what you were doing. Not good man. Like I said, nice job on the diy enclosure tho! 😁 . They also make steel versions of these inserts which imo are the way to go. So, to recap figure out what you want to do before you start filming. If it breaks while your installing it probably doing something incorrectly. When someone directs people to an actual builders forum where they can learn how to do things correctly and where they can access hundreds if not thousands of people’s knowledge to gain insight and learn, that is a contribution, much more so than posting a video of freehand slop hoping people will stroke your ego due to your massive insecurities. Which by the way are blatantly apparent based on your very emotional response. Byyyyye!

tech OMG It’s really strong.

I have a few that come by in the summer that are yellow.

I used to see them sometimes back when I lived in central Florida as well. Beautiful.

RJ RQ I had the power board rebuilt twice by Ernesto’s Electronics then something else broke and I threw it away for a TCL P607.

Edward Park Yes that is an option. I use the XT90 anti spark as a loop key.

Mikey Tongson which ones? The wood inserts, silver hex head, or the brass thumb screws?

More voltage keeps the amperage down which results in less heat and more efficiency.

Not out of the box with the VESC. It would also be difficult to hold while riding. There are many other R/C control mods that work as well. GT2B + BadWolf mod is one example.

All depends on the packaging. I went with 4 batteries so they could be thinner and I would have more ground clearance. The 6S 5000mah are much thicker.

Ok so you have more run time with the 4 3s vs 2 6s 5000 sorry to bother you batteries are my next step...

Exactly the same just thinner

@Carlton Harris Sorry I never replied. Lipo fully charged @ 4.2v per cell. In series: 4x3s@5000mah=12S=50.2v@5000mah, 2X6S@5000mah=12S=50.2v@5000mah. In parallel: 4x3S@5000mah=3S4P=12.6v@20000mah, 2x6S@5000mah=6S2P=25.2v@10000mah

I am building a desk and I have sk3 6364 Max Loading: 70A Can I buy a standard VESC 50A - 240A ???

motor amps are higher than battery amps because you only get full battery voltage when having close to 100% duty cycle... So motor load in amps should be whatever is specified as max amps for your motor... And your battery amps whatever your battery can output (divided by 2 if you are setting up 2 motors)

Chris Corum you are correct. Guess I could have posted what the problem was after replacing the pto clutch. Got an aftermarket one that is still running strong.

Gekko Productions knifekits.com

Michael M The VESC takes care of that. You can set the current limit on regen to the battery.

ggss11 doubtfoul

Yes I have a BMS and charger, but need to install it all. I just got my board running again. I blew the DRV on the VESC and now have a VESC 6. I need to make some more videos.

david martin To run or to charge? Would work either way, but if you want to charge in series you need to handle the balancing also. I made a short video on the harness: ua-cam.com/video/e52ib-lvpC0/v-deo.html

What does the sun do?

the black material you used to make the case for the electronics... could it be that it gets soft again when you heat it?

Elias Neururer You have to heat it to 300*+ F to even start to form it. Heat from the sun won't do a thing. They have been using this for years to make holsters and carry those things through a variety of climates and environments.

wow that's some nice material! need that too!!!

Barnes'd what is this material called!

It's a Landyachtz Canyon Arrow. The guy I got the pulley from never made any more. It's a 15mm drive setup. I am trying to find another source or might try to make some to sell.

The motor can handle 80A. You do not have to provide all of that. You can run it on less amperage. That is the same motor I have.

Max Loading: 80A Do you mean the ESC

diyelectricskateboard.com/products/torque-esc-vesc-bldc-electronic-speed-controller VESC is 50A continuous

What I mean is how I can determine the appropriate esc for the engine

ESC <= 80A

Nothing good ever came easy and I enjoy learning new things and sharing. So totally worth the effort.